RFS CELLFLEX Factory Fit Weatherproof 4.1-9.5 DIN Male to N Male 1/2" Low Loss Foam 4 Ft Jumper Cable

RFS CELLFLEX Factory Fit Weatherproof 4.1-9.5 DIN Male to N Male 1/2" Low Loss Foam 4 Ft Jumper CableRFS CELLFLEX foam dielectric jumper cables provide the ideal combination of low loss, high strength and highest flexibility for optimum performance. The use of jumpers provides greater flexibility if antennas are to be changed due to network upgrades, while the network is getting mature, reduced mechanical stress on antennas and connectors and better accessibility of feeder terminations (i. e. for troubleshooting). The RFS CELLFLEX SecureFit

RFS CELLFLEX foam dielectric jumper cables provide the ideal combination of low-loss, high-strength and highest flexibility for optimum performance. The use of jumpers provides greater flexibility if antennas are to be changed due to network upgrades, while the network is getting mature, reduced mechanical stress on antennas and connectors and better accessibility of feeder terminations (i.e. for troubleshooting).

The RFS CELLFLEX SecureFit Weatherproof 4.1-9.5 DIN Male to N Male 1/2" Low Loss Foam 4 Ft Jumper Cable is premium soldered and premium molded with fully soldered connectors. In general, it can be said that the soldered versions offer advantages with regard to intermodulation performance.

Passive third order intermodulation is a threat in mobile communication especially for multi-channel systems incorporating duplexers. For RFS jumpers the third order intermodulation is typically reduced to values below -155dBc (which means 155 dB lower than the two incident test carriers of +43 dBm). For RFS soldered connectors of the premium soldered, premium molded and factory fit jumper lines this value is improved to typically -162dBc.

The RFS CELLFLEX SecureFit Weatherproof 4.1-9.5 DIN Male to N Male 1/2" Low Loss Foam 4 Ft jumper cables are for indoor and outdoor applications and withstand severe environmental conditions. These jumper assemblies are watertight (transversally and longitudinally), providing additional safety even if humidity should enter the coaxial system. Additional sealing (e.g. weather-proofing kits) can be used but is not mandatory.

• Excellent contact force
• Low and stable intermodulation product (IM3)
• Excellent RF screening effectiveness
• Waterproof to IP 66/ 67/ 68
• Smaller connector footprint on 4.1-9.5 end enabling tighter spacing for connections
• Compliant to RoHS (EU) and CRoHS (China)

Structure

• Cable Type: 1/2" Low Loss Foam
• Jumper Type: Factory-Fit (Premium)
• Connector A: 4.1-9.5 DIN Male
• Center Contact Connector A: Brass, Silver plated
• Outer Contact Connector A: Brass, trimetal plated
• Coupling Nut Connector A: Hexagon nut, Nickel plated
• Connector B: N Male
• Center Contact Connector B: Brass, Silver plated
• Outer Contact Connector B: Brass, trimetal plated
• Coupling Nut Connector B: Hexagon nut, Nickel plated
• Dialectic: PTFE
• Gasket: Silicone Rubber
• Jacket: Black Polyethylene

• Length: 1.22 m (4 ft)
• Weatherproofing: Pre-assembled RFS boot
• Weatherproofing Material: Silicone
• UV Resistance: ASTM G155 for 1000 hours
• Minimum Bend Radius: 70 mm (3 in)
• Sealing Class: IP66/67/68 over operating temperatures
• Intermodulation: ≤ -159dBc (typical)
• Installation Temperature: -40° to 60°C (-40° to 140°F)
• Operation Temperature: -50° to 85°C (-58° to 185°F)
• Storage Temperature: -70° to 85°C (-94° to 185°)